Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
Are you hunting for answers about A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is additionally a moderately tough job. If the old bathtub is readily easily accessible, the project can move speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the task and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This short article will certainly aid you install a new tub in your shower room if you have actually currently acquired a new tub as well as do not require to transform the setup of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of removing the existing taps can be quite problematic due to the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Protect the faucet in position with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the tub in the called for placement. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and brand-new pipework for leakages and also tighten them if needed. Load the bath tub as well as likewise inspect the overflow outlet and the normal outlet for leakages.
Ultimately, repair the bath paneling as described in the producer's user's manual. Tiling and securing around the bathtub ought to wait until the bathtub has actually been made use of at the very least once as this will certainly resolve it into its final position.
Preparing for the Installation
To start with, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, bring about complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that article on Tools You Need to Install a New Bathtub through an acquaintance on a different website. Sharing is good. Helping people is fun. Thank-you for going through it.
Additional Information Report this page